google-site-verification=5hWSVQ193mCqPdre_SIGMP_ZjIHTvMflXnJnBO_Q35o پروژه با عنوان: تحلیل اتصالات چسبی فلز به کامپوزیت در کاربردهای فضایی
مجموعه فایل های آموزش مقدماتی تا پیشرفته نرم افزار کتیا (CATIA) و مجموعه کتب, جزوات, پروژه و مقالات تخصصی مهندسی مکانیک (ساخت و تولید, جامدات, سیالات)

پروژه با عنوان: تحلیل اتصالات چسبی فلز به کامپوزیت در کاربردهای فضایی
نویسنده : www.BartarFile.ir تاریخ : چهار شنبه 13 مرداد 1395

Within the European space programme, a new upper stage engine (Vinci) for the Ariane 5 launcher is being developed, and the Volvo Aero Corporation (VAC) is contributing with tur-bines for the fuel turbopumps. This MSc thesis investigates the possibility of designing the Turbine Exhaust Duct (TED) of the Vinci-engine in a carbon fibre composite material with adhesively attached titanium flanges. The focus of the project has been on stress analyses of the adhesive joints using Finite Element Methods (FEM), more specifically by using a cohe-sive zone material (CZM) to model the adhesive layer. Analysing adhesive joints is complex and an important part of the work has been to develop and concretise analysis methods for future use within VAC
To obtain the specialised material parameters needed for a CZM analysis, FE-models of ten-sile test specimens were analysed and the results compared to those of equivalent experimen-tal tensile tests. These parameters were then used when analysing the TED geometry with load cases specified to simulate the actual operation conditions of the Vinci engine. Both two-dimensional axisymmetric and fully three-dimensional models were analysed and, addition-ally, a study was performed to evaluate the effect of cryogenic temperatures on the strength of the joint
The results show that the applied thermal and structural loading causes local stress concentra-tions on the adhesive surface, but the stresses are not high enough to cause damage to the joint if a suitable joint design is used. Cryogenic temperatures (-150 °C) caused a significant strength reduction in the tensile specimens, partially through altered adhesive properties, but no such severe effects were seen in the temperature-dependent FE-analyses of the TED. It should be pointed out however, that some uncertainties about the material parameters exist, since these were obtained in a rather unconventional way. There are also several other impor-tant questions, beside the strength of the adhesive joint, that need to be answered before a metal-composite TED can be realised.

پروژه تحلیل اتصالات چسبی فلز به کامپوزیت در کاربردهای فضایی (Analysis of Metal to Composite Adhesive Joints in Space Applications)، مشتمل بر 7 فصل، 115 صفحه، به زبان انگلیسی، تایپ شده، به همراه تصاویر، با فرمت pdf به ترتیب زیر گردآوری شده است:

Chapter 1: PROJECT BACKGROUND

  • Volvo Aero Corporation
  • The Vinci Engine Project
  • The Turbine Exhaust Duct
  • The KOMET Research Project
  • Thesis Project Specifications

Chapter 2: THEORETIC BACKGROUND

  • Adhesive Joint Theory
  • Analytical methods
  • Numerical Analysis in Solid Mechanics
  • Introduction to Elastic FEA
  • Thermal FEA
  • Thermoelastic coupling
  • Cohesive Zone Material Modelling
  • Basic Concepts of Fracture Mechanics
  • The Cohesive Zone Model
  • CZM in ANSYS

Chapter 3: ANALYSIS METHODS

  • Obtaining CZM Material Parameters
  • Specimen modelling
  • Testing Procedure
  • 2D-axisymmetric TED Analysis
  • Simplified Geometry from Preliminary Study
  • Setup of the Finite Element Analysis
  • Material Data
  • Joint Geometry Concepts
  • Three-Dimensional TED Analysis
  • Load Extraction
  • 3D Modelling
  • Sub modelling
  • Analysis of Cryogenic Properties
  • Estimation of Cryogenic Material Parameters

Chapter 4: RESULTS

  • Obtaining Material Parameters
  • DOE 1 – Material Parameters
  • DOE 2 – Modelling Parameters
  • Typical Adhesive Stress Distribution
  • Final Parameters Resulting From the DOE Tests
  • 3D Validation Model
  • Axisymmetric TED Analysis
  • Preliminary Geometry – 40 mm Straight Overlap
  • Straight End – 25 mm overlap
  • Embedded Straight End Geometry
  • Short Tapered End Geometry
  • Fully Tapered End Geometry
  • 3D TED analysis
  • Static Structural Analysis
  • Coarse Model Transient Analysis
  • Submodel Result Plots
  • Cryogenic Properties Analysis

Chapter 5: DISCUSSION

  • Analysis of Tensile Test Specimens
  • Comparison of FEA and Screening Test Results
  • Conclusions of the DOE
  • Analysis of the TED Inlet Flange
  • Separate Load Analysis
  • Analysis of New Geometry Concepts
  • Analysis of the 3D Flange Model
  • Analysis of Cryogenic Properties
  • Potential Weight Savings

Chapter 6: CONCLUSIONS

  • CZM Analysis of Adhesive Joints
  • Review of the Analysis Procedure
  • Feasibility of a CFRP/Metal TED Design
  • Further Research Options

Chapter 7: REFERENCES

APPENDIX

  •  Cross section of the Vinci hydrogen turbo-pump
  • Flow chart of the Vinci engine (only lower stages shown)
  • ANSYS Code Sample – Tensile Test Specimen Analysis
  • ANSYS Code Sample – 2D Axisymmetric Analysis
  • ANSYS Code Sample – 3D Submodel Analysis

جهت دانلود پروژه تحلیل اتصالات چسبی فلز به کامپوزیت در کاربردهای فضایی (Analysis of Metal to Composite Adhesive Joints in Space Applications)، بر لینک زیر کلیک نمایید:

 

 

پروژه با عنوان: تحلیل اتصالات چسبی فلز به کامپوزیت در کاربردهای فضایی



نظرات شما عزیزان:

نام :
آدرس ایمیل:
وب سایت/بلاگ :
متن پیام:
:) :( ;) :D
;)) :X :? :P
:* =(( :O };-
:B /:) =DD :S
-) :-(( :-| :-))
نظر خصوصی

 کد را وارد نمایید:

 

 

 

عکس شما

آپلود عکس دلخواه:







:: موضوعات مرتبط: علم مواد و عملیات حرارتی، پروژه، ،
:: برچسب‌ها: کامپوزیت ها,


.:: This Template By : Theme-Designer.Com ::.